Digital Subscriber Line

Digital subscriber line (DSL, originally digital subscriber loop) is a family of technologies that provide Internet access by transmitting digital data over the wires of a local telephone network. In telecommunications marketing, the term DSL is widely understood to mean asymmetric digital subscriber line (ADSL), the most commonly installed DSL technology. DSL service is delivered simultaneously with wired telephone service on the same telephone line. This is possible because DSL uses higher frequency bands for data. On the customer premises, a DSL filter on each non-DSL outlet blocks any high frequency interference, to enable simultaneous use of the voice and DSL services.

The bit rate of consumer DSL services typically ranges from 256 kbit/s to 40 Mbit/s in the direction to the customer (downstream), depending on DSL technology, line conditions, and service-level implementation. In ADSL, the data throughput in the upstream direction, (the direction to the service provider) is lower, hence the designation of asymmetric service. In symmetric digital subscriber line (SDSL) services, the downstream and upstream data rates are equal.

Operation

Basic technology

Telephones are connected to the telephone exchange via a local loop, which is a physical pair of wires. Prior to the digital age, the use of the local loop for anything other than the transmission of speech, encompassing an audio frequency range of 300 to 3400 Hertz (voiceband or commercial bandwidth) was not considered. However, as long distance trunks were gradually converted from analog to digital operation, the idea of being able to pass data through the local loop (by utilizing frequencies above the voiceband) took hold, ultimately leading to DSL.

The local loop connecting the telephone exchange to most subscribers has the capability of carrying frequencies well beyond the 3.4 kHz upper limit of POTS. Depending on the length and quality of the loop, the upper limit can be tens of megahertz. DSL takes advantage of this unused bandwidth of the local loop by creating 4312.5 Hz wide channels starting between 10 and 100 kHz, depending on how the system is configured. Allocation of channels continues at higher and higher frequencies (up to 1.1 MHz for ADSL) until new channels are deemed unusable. Each channel is evaluated for usability in much the same way an analog modem would on a POTS connection. More usable channels equates to more available bandwidth, which is why distance and line quality are a factor (the higher frequencies used by DSL travel only short distances). The pool of usable channels is then split into two different frequency bands for upstream and downstream traffic, based on a preconfigured ratio. This segregation reduces interference. Once the channel groups have been established, the individual channels are bonded into a pair of virtual circuits, one in each direction. Like analog modems, DSL transceivers constantly monitor the quality of each channel and will add or remove them from service depending on whether they are usable.

ADSL supports two modes of transport: fast channel and interleaved channel. Fast channel is preferred for streaming multimedia, where an occasional dropped bit is acceptable, but lags are less so. Interleaved channel works better for file transfers, where the delivered data must be error free but latency (time delay) incurred by the retransmission of error containing packets is acceptable.

Because DSL operates above the 3.4 kHz voice limit, it cannot pass through a load coil. Load coils are, in essence, filters that block out any non-voice frequency. They are commonly set at regular intervals in lines placed only for POTS service. A DSL signal cannot pass through a properly installed and working load coil, while voice service cannot be maintained past a certain distance without such coils. Therefore, some areas that are within range for DSL service are disqualified from eligibility because of load coil placement. Because of this, phone companies endeavor to remove load coils on copper loops that can operate without them, and by conditioning other lines to avoid them through the use of fiber to the neighborhood or node (FTTN).

The commercial success of DSL and similar technologies largely reflects the advances made in electronics over the decades that have increased performance and reduced costs even while digging trenches in the ground for new cables (copper or fiber optic) remains expensive. Several factors contributed to the popularity of DSL technology:

• Until the late 1990s, the cost of digital signal processors for DSL was prohibitive. All types of DSL employ highly complex digital signal processing algorithms to overcome the inherent limitations of the existing twisted pair wires. Due to the advancements of Very-large-scale integration (VLSI) technology, the cost of the equipment associated with a DSL deployment lowered significantly. The two main pieces of equipment are a Digital subscriber line access multiplexer (DSLAM) at one end and a DSL modem at the other end.
• A DSL connection can be deployed over existing cable. Such deployment, even including equipment, is much cheaper than installing a new, high-bandwidth fiber-optic cable over the same route and distance. This is true both for ADSL and SDSL variations.
• In the case of ADSL, competition in Internet access caused subscription fees to drop significantly over the years, thus making ADSL more economical than dial up access. Telephone companies were pressured into moving to ADSL largely due to competition from cable companies, which use DOCSIS cable modem technology to achieve similar speeds. Demand for high bandwidth applications, such as video and file sharing, also contributed to popularize ADSL technology.

Most residential and small-office DSL implementations reserve low frequencies for POTS service, so that (with suitable filters and/or splitters) the existing voice service continues to operate independent of the DSL service. Thus POTS-based communications, including fax machines and analog modems, can share the wires with DSL. Only one DSL "modem" can use the subscriber line at a time. The standard way to let multiple computers share a DSL connection uses a router that establishes a connection between the DSL modem and a local Ethernet, Powerline, or Wi-Fi network on the customer's premises.

Once upstream and downstream channels are established, a subscriber can connect to a service such as an Internet service provider.

Naked DSL

A naked DSL (a.k.a. standalone or dry loop DSL) is a way of providing DSL services without a PSTN (analogue telephony) service. It is useful when the customer does not need the traditional telephony voice service because voice service is received either on top of the DSL services (usually Voice over IP) or through another network (mobile telephony).

It is also commonly called a "UNE" for Unbundled Network Element in the USA and known as a ULL service (Unconditioned Local Loop) in Australia. It has started making a comeback in the US in 2004 when Qwest started offering it, closely followed by Speakeasy. As a result of AT&T's merger with SBC, and Verizon's merger with MCI, those telephone companies have an obligation to offer naked DSL to consumers.

Even without the regulatory mandate, however, many ILECs offer naked DSL to consumers. The number of telephone landlines in the US dropped from 188 million in 2000 to 115 million in 2010, while the number of cellular subscribers has grown to 277 million (as of 2010). This lack of demand for landline voice service has resulted in the expansion of naked DSL availability.

Naked DSL products are also marketed in some other countries e.g. Australia, New Zealand and Canada.

Typical setup

On the customer side, the DSL Transceiver, or ATU-R, or more commonly known as a DSL modem, is hooked up to a phone line. The telephone company (telco) connects the other end of the line to a DSLAM, which concentrates a large number of individual DSL connections into a single box. The location of the DSLAM depends on the telco, but it cannot be located too far from the user because of attenuation between the DSLAM and the user's DSL modem. It is common for a few residential blocks to be connected to one DSLAM.

When the DSL modem powers up it goes through a sync procedure. The actual process varies from modem to modem but generally involves the following steps:

1. The DSL transceiver performs a self-test.
2. The DSL transceiver checks the connection between the DSL transceiver and the computer. For residential variations of DSL, this is usually the Ethernet (RJ-45) port or a USB port; in rare models, a FireWire port is used. Older DSL modems sported a native ATM interface (usually, a 25 Mbit/s serial interface). Also, some variations of DSL (such as SDSL) use synchronous serial connections.
3. The DSL transceiver then attempts to synchronize with the DSLAM. Data can only come into the computer when the DSLAM and the modem are synchronized. The synchronization process is relatively quick (in the range of seconds) but is very complex, involving extensive tests that allow both sides of the connection to optimize the performance according to the characteristics of the line in use. External, or stand-alone modem units have an indicator labeled "CD", "DSL", or "LINK", which can be used to tell if the modem is synchronized. During synchronization the light flashes; when synchronized, the light stays lit, usually with a green color.

Modern DSL gateways have more functionality and usually go through an initialization procedure very similar to a PC boot up. The system image is loaded from the flash memory; the system boots, synchronizes the DSL connection and establishes the IP connection between the local network and the service provider, using protocols such as DHCP or PPPoE. The system image can usually be updated to correct bugs, or to add new functionality.

The accompanying figure is a schematic of a simple DSL connection (in blue). The right side shows a DSLAM residing in the telephone company's central office. The left side shows the customer premises equipment with an optional router. This router manages a local area network (LAN) off of which are connected some number of PCs. With many service providers, the customer may opt for a modem which contains a wireless router. This option (within the dashed bubble) often simplifies the connection.

Exchange equipment

At the exchange, a digital subscriber line access multiplexer (DSLAM) terminates the DSL circuits and aggregates them, where they are handed off onto other networking transports. In the case of ADSL, the voice component is also separated at this step, either by a filter integrated in the DSLAM or by a specialized filtering equipment installed before it. The DSLAM terminates all connections and recovers the original digital information.

Customer equipment

The customer end of the connection consists of a terminal adaptor or "DSL modem". This converts data between the digital signals used by computers and the voltage signal of a suitable frequency range which is then applied to the phone line.

In some DSL variations (for example, HDSL), the terminal adapter connects directly to the computer via a serial interface, using protocols such as ethernet or V.35. In other cases (particularly ADSL), it is common for the customer equipment to be integrated with higher level functionality, such as routing, firewalling, or other application-specific hardware and software. In this case, the equipment is referred to as a gateway.

Most DSL technologies require installation of appropriate filters to separate, or "split", the DSL signal from the low frequency voice signal. The separation can take place either at the demarcation point, or with filters installed at the telephone outlets inside the customer premises. Either way has its practical and economical limitations.

Protocols and configurations

Many DSL technologies implement an Asynchronous Transfer Mode (ATM) layer over the low-level bitstream layer to enable the adaptation of a number of different technologies over the same link.

DSL implementations may create bridged or routed networks. In a bridged configuration, the group of subscriber computers effectively connect into a single subnet. The earliest implementations used DHCP to provide network details such as the IP address to the subscriber equipment, with authentication via MAC address or an assigned host name. Later implementations often use Point-to-Point Protocol (PPP) or Asynchronous Transfer Mode (ATM) (Point-to-Point Protocol over Ethernet (PPPoE) or Point-to-Point Protocol over ATM (PPPoA)), while authenticating with a userid and password and using Point-to-Point Protocol (PPP) mechanisms to provide network details.

Transmission methods

Transmission methods vary by market, region, carrier, and equipment.

• 2B1Q: Two-binary, one-quaternary, used for IDSL and HDSL
• CAP: Carrierless Amplitude Phase Modulation - deprecated in 1996 for ADSL, used for HDSL
• TC-PAM: Trellis Coded Pulse Amplitude Modulation, used for HDSL2 and SHDSL
• DMT: Discrete multitone modulation, the most numerous kind, also known as OFDM (Orthogonal frequency-division multiplexing)